2.Pontoons and piers

Reinforced concrete and plastic pontoons

The Adamant Shipyard enterprise produces reinforced concrete and plastic pontoons, floats, piers and platforms on reinforced concrete and plastic floats, mooring “fingers”, buoys, ladders, anchors for the installation of floating structures, additional equipment for arranging yacht clubs and moorings, floating structures on pontoons used as workshops, service, administrative, commercial or residential buildings, rack-mount and self-propelled vessels for the construction and maintenance of yacht marinas.

Adamant Shipyard provides a full range of services necessary for the construction of yacht parking - from concept development, design, payback calculation, to turnkey construction:

- development of configuration and design;

- design;

- production and supply of equipment;

- installation supervision or turnkey installation of equipment;

- warranty and post warranty service.

Design and construction of yacht clubs and moorings

Equipment for the construction, maintenance and operation of yacht marinas, floating structures, private, commercial and passenger berths

Подробнее

Pontoons, 2.4 meters wide, are mainly used for the construction of mooring berths for pleasure boats, private berths, pedestrian floating bridges. Their use for the construction of floating sites and other structures is not advisable.

Pontoons, 3 meters wide, are used for the construction of mooring berths of large length, with the possibility of using electric vehicles to move around the pontoons. It is very convenient and practical to use these pontoons for the construction of various floating structures, regulating the receipt of the necessary displacement by the height of the side of the pontoons.

Pontoons, with a side height of 0.9 meters, are used for the construction of mooring berths and open floating areas for small loads and not long lengths.

Pontoons, with a side height of 1.15 meters, are used for the construction of mooring berths, floating structures with a permissible significant load, according to the project.
Pontoons, with a side height of 1.45 meters, are intended for the construction of various floating heavy structures. Withstand heavy loads. It is forbidden to use these pontoons in one at a time due to their low stability and large useful displacement. United by two or more pontoons with a long side are ideally suited for the construction of mooring berths for large pleasure boats and other vessels and the construction of large floating structures.

The large mass of reinforced concrete pontoons provides good stability for the entire floating structure with a low center of gravity, even with several floors.

PONTOONS AND FLOATING AREAS ASSEMBLED ON OUR PONTONS DO NOT REQUIRE CURRENT MAINTENANCE FOR THE WHOLE USE.
OUR PONTONS DO NOT REQUIRE PERIODIC FORCING FOR THEIR INSPECTION AND REPAIR.
ALL METAL COMPONENTS OF PONTONS IN A FLOATING AREA, FOR THE CONSTRUCTION OF FLOATING HOUSES, ARE PERFORMED ACCORDING TO THE CALCULATION OF THEIR OPERATION AT LEAST 120 YEARS IN SEA WATER.

Design and construction of yacht clubs and moorings

Reinforced concrete pontoons

Reinforced concrete pontoons manufactured by Adamant Shipyard are made of hydraulic concrete with special additives, reinforced with fiber, the surface layer of reinforced concrete is impregnated with a special compound, which makes it several times stronger and absolutely waterproof. The pontoon is designed and manufactured according to the rules for the construction of ships from reinforced concrete. It has a powerful internal set, bulkheads, stiffeners, built-in lifting eyes, anchor tunnels at the corners, for installing pontoons using the anchor chain and anchors, with special locking locks to adjust the length of the anchor chain. To connect the pontoons in length on the short side of the pontoons are niches for installing rubber-metal joints of pontoons. Inside the pontoons, along the long sides, there are tunnels for wiring power cables, water pipes, sewers, etc.
After manufacturing the pontoon, all internal voids are filled with special polystyrene foam. This makes the pontoon completely unsinkable even with mechanical damage to the sides.

Lightweight reinforced concrete pontoons - designed for the construction of small marinas, private moorings, floating sites. Places of installation of the lake, river, reservoir. Freeboard 370-430 mm, depending on the installed deck equipment.

Reinforced concrete floats (small pontoons) - designed for the construction of moorings, floating sites, light houseboats and other lightweight floating structures. Reinforced concrete floats are interconnected by a wooden or metal frame. Floating structures assembled on reinforced concrete floats are ideal for swimming and mooring of private water transport, they are economically viable and have a long service life. Places of installation of the lake, river, reservoir.

поплавок железобетонный (1)

1/42

Plastic floats - designed for the construction of moorings, floating platforms, transitional ladders and other light floating structures. Plastic floats are interconnected by a wooden or metal frame. Floating constructions assembled on plastic floats are ideal for swimming and mooring of private water transport, they are cost-effective and have a long service life. Plastic floats are made of high-density polyethylene, low pressure PEHD, by vacuum molding and welding, filled with special polystyrene foam, which makes them completely unsinkable. Places of installation of the lake, river, reservoir.

Equipment for moorings and marinas - the range of equipment manufactured by Adamant Shipyard is the widest in the industry of construction of moorings and marinas, able to satisfy the most diverse wishes and requests of customers. The equipment includes everything you need for marinas and private berths. All equipment is of excellent quality, has a long service life and is economically viable.

Грунтовые якоря-буры являются наиболее простыми и удобными решениями инженерных задач по закреплению различных конструкций и предметов в промышленном и гражданском строительстве, морском строительстве, ландшафтных и садово-парковых работах, и других специализированных рынках.